Hole saws: discover how to make through holes with Dinamitek

Dinamitek presents the guide for making through holes with hole cutters

To make large-diameter cylindrical through holes with well-defined contours, use hole cutters. These are concave cylindrical bits. When you want to make a blind hole, you need to chisel away the waste material, called the "core hole."

To choose the hole saw, evaluate the material you want to drill and the diameter of the hole you want to make.

Standard hole saws are suitable for drilling in wood, drywall and softer materials

Diamond hole saws are suitable for drilling into harder materials such as tiles, stoneware, or granite . Hard materials are drilled with water, at low speed and without impact. Water should not be used on porous, absorbent materials, so they are drilled dry. The most common porous materials are aerated concrete or plaster.

The hole saw is used with the drill and the screwdriver .

For private home maintenance you can use a 14 Volt drill driver,
For professional use it is better to opt for at least an 18 Volt drill.

For what jobs should I use the cup saw?

to fix a hinge to a door,
to fix a new switch to the wall,
run a pipe through the wall,
to insert a tap into the stainless steel sink top

How do you use a cup cutter?

Drilling with a hole saw isn't much different from drilling with other types of bits; it's just important to take some precautions to avoid mistakes. You risk damaging the hole saw, burning out the drill motor, or damaging the surface if you're not careful.

First and foremost, the essential tool for the hole saw is the pilot bit, which guides the cutter and holds it in place while drilling the hole. The pilot bit is placed at the center of the hole saw and will be used to mark the center of the hole to be drilled. By lowering the pilot bit, the teeth of the hole saw will sink into the material, and drilling can begin.

Hole saw cutting is sensitive to sawdust, so keep the bit, tool, and surface clean to avoid jamming and overheating the drill and cutter. If necessary, slowing the rotation and withdrawing the tool allows the cutter to cool and remove any buildup.

Do not bend the tool while using or at the end of drilling, extracting it parallel to the groove created;

respect the instructions for use , which include a correct number of turns of the drill, the exclusion of the percussion mode where required or, on the contrary, the insertion with some cutters that require it;

Some softwoods tend to "clog" the tool. In these cases, the hole saw can be used only as a guide to mark the surface and the diameter of the hole. Drilling a series of small holes within the hole saw's mark with a standard wood drill bit will facilitate the final cut with the hole saw and ensure a precise, clean finish. Of course, this will increase the number of passes, but it won't damage either the equipment or the surface you're working on. The material always dictates the procedures and tools to use; to achieve good results, you need to be patient and adapt.

The hole saw , in addition to drilling, is also very useful for enlarging holes. In this case, obviously, you can't rely on the pilot drill. The solution is to use plywood and a vice. The plywood sheet, properly secured, will serve as a surface for tracing the hole with the hole saw. This is the usual procedure because the surface to be drilled is restored and can accommodate the pilot drill. When drilling on elements that don't allow for this solution, such as doors and panels, simply secure an additional sheet of plywood to the outside, so the cut will be made firmly and precisely.

How does the use of the hole saw change when drilling hard materials?
In construction, the hole saw is widely used for drilling holes in walls, but what material is it made of?
Cement, concrete mixes, reinforced concrete, bricks, etc., all these and other materials can be found in the wall.

In addition to the usual precautions, when drilling hard materials, be careful not to force the hole . When you feel the tool struggling, it's a good idea to remove the hole saw using the drill's autoreverse function, wait a few seconds, and try again. The material in the way will gradually be removed, without compromising the quality of the work. Increased friction should never correspond to increased pressure ; instead, it's better to proceed gradually.

Various types of cup cutters are used in construction

Standard construction cutter (rotation) for bricks, tuff, bricks
heavy-duty hole saws (roto-percussion) for concrete, conglomerates, stone and masonry (shallow, superficial holes)
Heavy-duty core bits for concrete, conglomerate, stone, and masonry (deep holes, heavy-duty work) to be mounted on heavy-duty drills. These tools are designed for professional builders.
diamond drill bits for reinforced concrete, without this specific tool you will only get burnt drills and broken tools
Diamond hole saws (for special materials) for thin slabs of marble, granite, and fiberglass, specially designed to avoid damaging these resistant yet fragile materials. The hole is made without excessive force on the material.

These tips will help you carry out all your home maintenance work and create DIY projects.

Take me to the tool catalog