Electric chain hoist vt trolley type with mechanical translation, three-phase current supply at one lifting speed PHOLGOR .
Supply voltage 380/50V/Hz. Three-phase, asynchronous, self-braking motor with single polarity
48V low voltage controls
Chain catcher for idle chain included. It is a soft bag made of plastic material
Electric chain hoist for the vertical lifting of free loads in space, with mechanical chain driven trolley
The trolleys translate the load horizontally along the longitudinal axis of the sliding beam positioned at a height. The sliding beam is double T
The hoist and trolley have an IP 45 protection index and class "F" insulation
The following versions are available
vt 85: capacity Kg 125 with 1 section of chain, lifting/translation speed m/min 8, power Kw0.4, weight (with ~3 m of chain) Kg 43
vt 90: capacity Kg 200 with 1 section of chain, lifting/translation speed m/min 8, power Kw0.4, weight (with ~3 m of chain) Kg 43
vt 95: capacity Kg 250 with 1 section of chain, lifting/translation speed m/min 8, power Kw0.4, weight (with ~3 m of chain) Kg 43
vt 100: capacity Kg 500 with 1 section of chain, lifting/translation speed m/min 8, power Kw0.9, weight (with ~3 m of chain) Kg 51
vt 105: capacity Kg 1000 with 1 section of chain, lifting/translation speed m/min 6.3, power Kw1.6, weight (with ~3 m of chain) Kg 78
vt 110: capacity Kg 500 with 2 sections of chain, lifting/translation speed m/min 4, power Kw0.4, weight (with ~3 m of chain) Kg 46
vt 115: capacity Kg 1000 with 2 sections of chain, lifting/translation speed m/min 4, power Kw0.9, weight (with ~3 m of chain) Kg 59
vt 120: capacity Kg 2000 with 2 sections of chain, lifting/translation speed m/min 3.15, power Kw1.6, weight (with ~3 m of chain) Kg 94
Below is the framework of the environmental conditions of use:
.Operating temperature min -10 degrees max +40 degrees centigrade
.Maximum relative humidity 85 %
.Maximum altitude 1000 meters above sea level
.Noise dB(A): less than 80 decibels
characteristics of the hoists:
The hoist has a light alloy body. The gearbox casing is closed in a grease bath, with the heat-treated steel gears, which rotate thanks to ball bearings. The honeycomb loading nut is milled in steel.
The ring chain is very resistant, in steel with a special anti-wear treatment which makes the surface further hardened. The high-strength hook is made of pressed steel. The lower one rotates on ball bearings. A very useful safety carabiner prevents unhooking.
The load limiter and the lifting limit switch are very useful for the safety of the operator and the material being lifted. The load limiter is a friction device that stops movement in the event of an overload; the lifting limit switch is an electric device which limits the maximum upward and downward stroke.
The trolley has steel bearing plates. Each plate has two pins that accommodate the two wheels. The wheels are machined and made in cast iron; they have a guide edge and can rotate thanks to ball bearings. The plates need to be connected to the sliding beam; the adjustable tie rods allow the connection to be adapted according to the width of the flange of the beam itself. Adjustable tie rods are fitted with shim washers and lock nuts; they also have a safety device against unscrewing.
The vt-type electric chain hoist with mechanical translation trolley has a cast iron operating handwheel. The movement at the wheels comes from the movement of the chain. The operating chain is made of galvanized steel so it is very resistant to wear.
Product compliant with the Community Machinery Directive N 2006/42/CE and with the Low Voltage Directive 2006/95/CE and with the Electromagnetic Directive 2004/108/CE
With:
EC Declaration of Conformity (or Manufacturer's Declaration)
test certificate or suitability for use
user instruction manual
