Suspension type vt electric chain hoist, three-phase current power supply at one lifting speed PHOLGOR
Available
vt 5: capacity Kg 125 with 1 section of chain, lifting/translation speed m/min 8, power Kw0.4, weight (with ~3 m of chain) Kg 35
vt 10: capacity Kg 200 with 1 section of chain, lifting/translation speed m/min 8, power Kw0.4, weight (with ~3 m of chain) Kg 35
vt 15: capacity Kg 250 with 1 section of chain, lifting/translation speed m/min 8, power Kw0.4, weight (with ~3 m of chain) Kg 35
vt 20: capacity Kg 500 with 1 section of chain, lifting/translation speed m/min 8, power Kw0.9, weight (with ~3 m of chain) Kg 43
vt 25: capacity Kg 1000 with 1 section of chain, lifting/translation speed m/min 6.3, power Kw1.6, weight (with ~3 m of chain) Kg 66
vt 30: capacity Kg 500 with 2 sections of chain, lifting/translation speed m/min 4, power Kw0.4, weight (with ~3 m of chain) Kg 38
vt 35: capacity Kg 1000 with 2 sections of chain, lifting/translation speed m/min 4, power Kw0.9, weight (with ~3 m of chain) Kg 47
vt 40: capacity Kg 2000 with 2 sections of chain, lifting/translation speed m/min 3.15, power Kw1.6, weight (with ~3 m of chain) Kg 75
Valuable solution for the vertical lifting of loads free in space. 1-speed electric chain hoist. Suitable for light loads. It is recommended to respect all the vestments of use and to observe the due safety standards.
In a chain hoist there are 2 fundamental components: the hoist and the chain. Below are the characteristics of the 2 elements
The body of the hoist is in light alloy with the gearbox casing closed in a grease bath. The reducer has heat treated steel gears. The gears are rotatable thanks to ball bearings. The loading nut is made with alveoli, milled in steel. The hook is made of high resistance pressed steel. The lower one rotates thanks to ball bearings, and has a safety snap hook against unhooking.
The link chain is made of high strength steel. Thanks to the anti-wear treatment, it is hardened on the surface for a long life. The chain collector is a soft bag made of plastic material, in which the inactive chain resides.
The hoist is equipped with a very effective safety system: the load limiter. It consists of a clutch device which intervenes by stopping the movements of the equipment in the event of an overload. Another very useful device, also for the purposes of safety for the load and the operators, is the lifting limit switch: an electric device which limits the maximum up and down stroke.
The hoist features IP 45 protection level with "F" insulation class which represents the maximum temperature appropriate for that product under normal operating conditions. Class F corresponds to a temperature of 155 degrees Celsius. The operating temperature greatly influences the aging especially of the insulating materials, knowing this parameter is important for a good use of the equipment. The IP 45 degree of protection means that it is protected against the ingress of solid objects larger than 1mm in diameter and is protected against jets of water pumped from any direction.
The hoist is powered by alternating electric current with three-phase voltage 220/380 V - 50 H. The hoist motor is asynchronous three-phase, single polarity and self-braking for maximum safety of the load and the operators.
The 48 V low voltage controls, LV pendant push-button panel, have IP 55 protection level
Below is the framework of the environmental conditions of use, which must be strictly observed
Operating temperature min -10 degrees max +40 degrees centigrade
Maximum relative humidity 85%
Maximum altitude 1000 meters above sea level
Noise dB(A): less than 80 decibels
The hoist has the CE marking, is supplied with the CE declaration of conformity or the manufacturer's declaration; Certificate of testing or suitability for use and instruction manual.
PHOLGOR hoists are manufactured in compliance with the Community Machinery Directive No. 2006/42/EC, the Low Voltage Directive 2006/95/EC and the Electromagnetic Compatibility Directive 2004/108/EC
